(ASTM A673, A370) Bend Test Standard size, 17 foot pounds (23 joules) @ - 40deg C/F test temp, transverse direction hardness 363BHN. 4T (up to .50inches - 12.5mm:Flatness:Standards are 50% of that specified in ASTM A-6. Special tolerances are available. Thickness:The standards are 50% of that specified in ASTM A-6. Special tolerances are
ASTM A 392, Federal specification RR-F-191 Type I, (1) Red text indicates conformance with ASTM A-392. (2) Breaking strength (Table 1) based on a minimum tensile strength of 75,000 psi. (3) 11 ga. fabric available with a Class 1 coating only. (4) Fabric with mesh size less than 1-3/4 in. is galvanized before weaving.
ASTM A871 Grade 65. A high strength, grade 65, low alloy structural (copper bearing) steel plate with atmospheric corrosion resistance intended for use in tubular structures, transmission towers, and poles. Weathering Steel Charpy tested Plate from ISO 9000/9002 sources MEMBER of ASME
ASTM and SAE Specifications, Proof Loads & Tensile Size (Inches) Proof Load psi Tensile Strength min. psi; SAE Grade 1 ASTM A307:Low Carbon Steel:1/4 thru 1-1/2 1/4 thru 1-1/2 Over 1-1/2 thru 4:33000 33000:60000 60000 55000:SAE Grade 2:Low Carbon Steel:1/4 thru 3/4 Over 3/4 thru 1-1/2:55000 33000:74000 60000:SAE Grade 3:
Brick Sizes, Shapes, Types, and Grades - archtoolboxThe actual dimensions of the brick are within certain tolerances of the specified size tolerances are spelled out in ASTM C216, Standard Specification for Facing Brick and ASTM C652, Standard Specification for Hollow Brick. The tolerances vary depending on the type and size of brick, but they are minimal and will usually not affect the
ASTM levels determined by ASTM F2100-11 standards 1 Key Group, AAMI Knowledge Research, June 2017 The 4 Fs of selecting the right mask *Use ASTM standards to support choices around Filtrations and Fluid Resistance Procedure Masks ASTM Level 1 Patient & Staff isolation:Clean environments, sterile cores, processing departments, ER and
Concrete Pipe Use ManualI. Introduction 1 II. Storm Sewers & Culverts Introduction 2 Specifications Circular Pipe (ASTM C14, C76, C655) 2 Arch Pipe (ASTM C506) 3 Elliptical Pipe (ASTM C507) 3 Precast Concrete Box Sections (ASTM C1577) 3 Burial Tables
Designation:C216 104.1.1 Type FBSBrick for general use in masonry. 4.1.2 Type FBXBrick for general use in masonry where a higher degree of precision and lower permissible variation in size than permitted for Type FBS is required. 1 This specication is under the jurisdiction of ASTM Committee C15 on
4.1.1 Type FBSBrick for general use in masonry. 4.1.2 Type FBXBrick for general use in masonry where a higher degree of precision and lower permissible variation in size than permitted for Type FBS is required. 1 This specication is under the jurisdiction of ASTM Committee C15 on
Heavy Hex Structural Bolt Assembly, A325, Type 1, Heavy 1 1/2 3.000 1.625 .136 .177 C Size Specification Requirements: Dimensions:Heavy Hex Structural Bolt:ASME B18.2.6 Heavy Hex Nut:ASME B18.2.2 Structural Washer:ASTM F436, Type 1 Material & Heavy Hex Structural Bolt:ASTM F3125, Grade A325, Type 1 Mechanical Properties:Heavy Hex Nut:ASTM A563 Grade C, C3, D, DH or DH3 (ASTM
Material Specification 523Rock for RiprapASTM D 4992 provides guidance on selecting rock from a source. Except as otherwise provided, the rock shall be tested and shall have the following properties:Rock type 1 Bulk specific gravity (saturated sur-face-dry basis)Not less than 2.5 when tested in accordance with ASTM C 127 on samples prepared as described for sound-ness testing.
ASTM C533 Type I Material Specification:Passes ASTM C1617 Corrosion:Passes ASTM C795 / C871 / C692 Corrosion Austenitic Stainless Steel:Passes Pipe Insulation ½ -24 / 15-600 1/25 (Only Up to 6/150mm Pipe Size) - 4/102 Quad Segments 24 -40 / 600-1000 1 ½-3 / 38-76
Speci cation Sheet - CertainTeedGate opening of 8", transmission set in 2nd gear, and air pressure of 1.4-1.6 psi Pro Installers use settings Gate opening of 11", transmission set in 3rd gear, and air pressure of 2.4-2.6 psi Hose transition sleeves when necking down in hose size R-Values are determined in accordance with ASTM C687. Complies with ASTM C764 as Type 1 insulation.
Specification for Structural Joints Using ASTM A325 or Section 6.2.1 was modified to permit the use of A490 type bolts, with round heads equal or larger in diameter than ASTM F1852 heads, without F436 hardened washers. Table 6.1, footnote d, was added to clarify use of non-hardened plate washer to be used in conjunction with an ASTM
Per FDA guidance, the particle size is 0.1 microns and the particles are non-neutralized for medical face masks. 4. Test method for resistance of medical face masks to penetration by synthetic blood (horizontal projection of fixed volume at a known velocity) (F1862/F1862M)
Structural Quality High Strength/Low Alloy Abrasion T-1 Type A (ASTM A514 Grade B) Available in thicknesses through 11/4. Has a lower alloy content than the original T-1 with the same strength. T-1 Type B (ASTM A514 Grade H) Available 13 8 through 2 with an alloy content between Type A and the original T-1. Maintains the same strength as original T-1.ASTM Weathering Steel Specifications Central Steel ServiceASTM A871-65. ASTM A871-65 is a high strength low-alloy structural steel plate with improved atmospheric corrosion resistance. This specification provides for a 65ksi minimum yield strength and an 80ksi minimum tensile strength plus the atmospheric corrosion resistance of this steel in most environments is substantially better than that of